一、安装所需的软件包： pptpd-*.rpm ppp-*.rpm pptp-*.rpm 一般情况下系统已经将pptp和ppp包安装好了，所以只需安装pptpd（pptpd server的守护进程）包就ok。利用suse linux 自带的yast工具安装非常方便，可以自动解决依赖关系。 二、配置文件。 /etc/pptpd.conf /etc/ppp/chap- secrets /etc/ppp/ options.ppp0（注： options.ppp0文件是由 options.pptp文件复制而来） 下面是各文件具体配置： 1、 /etc/pptpd.conf
################################################################################
#
# Sample PoPToP configuration file
#
# for PoPToP version 1.0.0
#
################################################################################
# TAG: speed
#
# Specifies the speed for the PPP daemon to talk at.
# Some PPP daemons will ignore this value.
#
speed 115200
# TAG: option
#
# Specifies the location of the PPP options file.
# By default PPP looks in '/etc/ppp/options'
#
#option /this/is/the/options/file
option /etc/ppp/options.ppp0
# TAG: debug
#
# Turns on (more) debugging to syslog.
#
debug
# TAG: localip
# TAG: remoteip
#
# Specifies the local and remote IP address ranges.
#
# You can specify single IP addresses seperated by commas or you can
# specify ranges, or both. For example:
#
# 192.168.0.234,192.168.0.245-249,192.168.0.254
#
# IMPORTANT RESTRICTIONS:
#
# 1. No spaces are permitted between commas or within addresses.
#
# 2. If you give more IP addresses than MAX_CONNECTIONS, it will
# start at the beginning of the list and go until it gets
# MAX_CONNECTIONS IPs. Others will be ignored.
#
# 3. No shortcuts in ranges! ie. 234-8 does not mean 234 to 238,
# you must type 234-238 if you mean this.
#
# 4. If you give a single localIP, that's ok - all local IPs will
# be set to the given one. You MUST still give at least one remote
# IP for each simultaneous client.
#
#localip 192.168.0.234-238,192.168.0.245
#remoteip 192.168.1.234-238,192.168.1.245
localip 10.10.10.10 //指定vpn服务器的地址，可以是虚拟的ip。
remoteip 192.168.137.128-200 //指定客户端连上后，分配的ip在此指定的范围
# TAG: ipxnets
#
# This gives the range of IPX networks to allocate to clients. By
# default IPX network number allocation is not handled internally.
# By putting a low and high network number here a pool of IPX networks
# can be defined. If this is done then there must be one IPX network
# per client.
#
# The format is a pair of hex numbers without any 0x prefix separated
# by a hyphen.
#
#ipxnets 00001000-00001FFF
# TAG: listen
#
# Defines the IP address of the local interface on which pptpd
# should listen for connections. The default is to listen on all
# local interfaces (even ones brought up by pptp connections, thus
# permitting pptp tunnels inside the pptp tunnels).
#
#listen 192.168.0.1
listen 10.10.10.10
# TAG: pidfile
#
# This defines the file name in which pptpd should store its process
# ID (or pid). The default is /var/run/pptpd.pid.
#
pidfile /var/run/pptpd.pid |
